| Customization: | Available |
|---|---|
| Frequency Range: | 400-700MHz/700-1050MHz |
| Application: | Drone Jammer |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
|
Item
|
Indicator requirements
|
remarks
|
|
Frequency (Mhz)
|
400-700MHz
|
|
|
Signal mode
|
DDS
|
|
|
Saturated Output Power
|
50 ± 1dBm
|
|
|
Large Signal Gain
|
50±1dB
|
|
|
Gain Flatness
|
≤4.0dB
|
|
|
Gain Stability
|
± 1.5dB
|
at -25+55
|
|
Power stability
|
± 1.5dB
|
at -25+55
|
|
DC Input Voltage
|
DC28±1.0V
|
|
|
Current Consumption
|
10.5A typ;
12.5A max
|
@ Pout=100W CW, 50 ohms load |
|
Current Consumption
|
10.5A typ;
12.5A max
|
@ Pout=100W CW, 50 ohms load |
|
Monitoring interface
|
7W2 Connector: A1: GND; A2: +28V; PIN1: RS485A; PIN2: RS485B; PIN3: GND; PIN4: NC; PIN5: Power amplifier enable switch,High level +5V off, low level 0V on. |
|
|
Monitoring type
|
RS485Baud rate 19200
|
|
|
Monitoring function
|
1. Power amplifier query:module status (including power amplifier status, over temperature alarm, standing wave ratio alarm, power amplifier fault alarm); 2. Power amplifier enable switch: Turn on or off the power amplifier. 3. Over temperature alarm: The temperature threshold is +85. If the detected temperature exceeds +85, an alarm will be triggered, and the power amplifier will be turned off. When it reaches +65, the power amplifier will be turned on; 4. Power amplifier standing wave alarm:When the power amplifier standing wave detection is greater than 4.0, the power amplifier starts protection; 5. Overvoltage alarm of power amplifier:When the power amplifier voltage exceeds 32V, the power amplifier will automatically shut down; 6. Power amplifier undervoltage alarm: When the power amplifier voltage is below 24V, the power amplifier will automatically shut down |
|
|
RF output connector
|
N-K
|
|
|
Dimension
|
200×120×24mm
|
|
|
Installation Dimension
|
194×114×24mm
|
|
|
Screw Size
|
4-Ø4.2mm
|
|
|
Item
|
Indicator requirements
|
remarks
|
|
Frequency (Mhz)
|
700-1050MHz
|
|
|
Bandwidth rang (Mhz)
|
350M
|
|
|
Maximum output power (dBm)
|
50 ± 1dBm
|
|
|
Large Signal Gain
|
50±1dB
|
|
|
Gain Flatness
|
≤3.0dB
|
|
|
Gain Stability
|
± 1.5dB
|
at -25+55
|
|
Power stability
|
± 1.5dB
|
at -25+55
|
|
DC Input Voltage
|
DC28±1.0V
|
|
|
Current Consumption
|
10.5A typ;
12.5A max
|
@ Pout=100W CW, 50 ohms load |
|
Monitoring interface
|
7W2 Connector: A1: GND; A2: +28V; PIN1: RS485A; PIN2: RS485B; PIN3: GND; PIN4: NC; PIN5: Power amplifier enable switch,High level +5V off, low level 0V on. |
|
|
LTD pilot lamp
|
POWERPower Supply pilot lamp RUNRun pilot lamp ALARMFault alarm pilot lamp. |
|
|
Monitoring type
|
RS485Baud rate 19200
|
|
|
Monitoring function
|
1. Power amplifier query:module status (including power amplifier status, over temperature alarm, standing wave ratio alarm, power amplifier fault alarm); 2. Power amplifier enable switch: Turn on or off the power amplifier. 3. Over temperature alarm: The temperature threshold is +85. If the detected temperature exceeds +85, an alarm will be triggered, and the power amplifier will be turned off. When it reaches +65, the power amplifier will be turned on; 4. Power amplifier standing wave alarm:When the power amplifier standing wave detection is greater than 4.0, the power amplifier starts protection; 5. Overvoltage alarm of power amplifier:When the power amplifier voltage exceeds 32V, the power amplifier will automatically shut down; 6. Power amplifier undervoltage alarm: When the power amplifier voltage is below 24V, the power amplifier will automatically shut down |
|
|
RF output connector
|
N-K
|
|
|
Dimension
|
170×79.5×24mm
|
|
|
Installation Dimension
|
164×73.5×24mm
|
|
|
Screw Size
|
4-Ø3.2mm
|
|
){kind=link}